PG-1 Aqua Glider | |
---|---|
Role | Glider |
National origin | United States |
Manufacturer | Explorer Aircraft |
Designer | Bill Skiliar |
First flight | 1959 |
Introduction | 1959 |
Number built | at least four[1] |
The Explorer PG-1 Aqua Glider is an American single seat, biplane glider that was designed by Bill Skiliar in 1959 and made available as plans for amateur construction. The prototype was built with help from a troop of Air Explorer Scouts that same year.[2][3][4]
Design and development
Skiliar was a Colonel in the USAF and an aeronautical engineer and test pilot. He designed the Aqua Glider to be towed behind a boat, taking off from the water, releasing the tow rope and then gliding to a landing on the water.[2][3][4]
The Aqua Glider is made from wood and covered with doped aircraft fabric. The landing gear is fixed and consists of a pair of water skis. The aircraft uses spoilers instead of ailerons for roll control and features an all-flying tail and a trim system. The biplane wing employs a NACA 4412 airfoil.[2][3][4]
The aircraft is towed behind a ski tow boat, lifting off at 35 mph (56 km/h) and climbing to about 200 ft (61 m), depending on the length of the tow rope used. The aircraft does not stall, but enters a nose-high mushing condition with a slow rate of descent.[3][4]
Plans were sold for US$25 by Corben Development Corporation of Venice, Florida and completed aircraft cost about US$800 in materials in 1983.[3]
Skiliar made several modifications to the design, experimenting with landing gear for land use made from automobile leaf springs. He also created a powered version with two McCulloch MC-70 go-cart engines mounted in the aft fuselage behind the wing spar, with the propeller above the engines on a streamlined pylon that housed the drive chains. The powered version was not successful and was returned to glider configuration.[4]
Operational history
By 1983 the prototype had flown over a thousand flights and plans had been widely sold in the United States and many other countries.[3]
Aircraft on display
- EAA AirVenture Museum – the prototype was donated to the museum in 1970[4][5]
Specifications (variant specified)
Data from Sailplane Directory, Soaring and EAA[2][3][6]
General characteristics
- Crew: One
- Length: 13 ft 8 in (4.17 m)
- Wingspan: 16 ft 0 in (4.88 m)
- Wing area: 95 sq ft (8.8 m2)
- Aspect ratio: 5:1
- Airfoil: NACA 4412
- Empty weight: 180 lb (82 kg)
- Gross weight: 400 lb (181 kg)
Performance
- Maximum speed: 65 mph (105 km/h, 56 kn)
- Stall speed: 35 mph (56 km/h, 30 kn)
- Maximum glide ratio: 6/5:1 at 45 mph (72 km/h)
- Wing loading: 4.5 lb/sq ft (22 kg/m2)
See also
Related lists
References
- ^ Federal Aviation Administration (May 2011). "Make / Model Inquiry Results". Retrieved May 10, 2011.
- ^ a b c d Activate Media (2006). "PG-1 Aqua Glider Explorer". Archived from the original on March 8, 2012. Retrieved May 10, 2011.
- ^ a b c d e f g Said, Bob: 1983 Sailplane Directory, Soaring Magazine, page 40. Soaring Society of America November 1983. USPS 499-920
- ^ a b c d e f EAA AirVenture Museum, 2011, Skiliar Aqua Glider “Explorer” – N6498D http://www.airventuremuseum.org/collection/aircraft/Skliar Aqua Glider.asp, accessed 10 May 2011
- ^ Federal Aviation Administration (May 2011). "Make / Model Inquiry Results". Retrieved May 10, 2011.
- ^ EAA AirVenture Museum, 2011, Skiliar Aqua Glider “Explorer” – Specifications http://www.airventuremuseum.org/collection/aircraft/Skliar Aqua Glider Specifications.asp, accessed 10 May 2011